Level 2 – as seen in the FAQ's on how we sell our boards in 3 levels
The #1 seller with Trailer Trash PedalBoards is our Level 2. We sell board/case prepped with power supplies and accessories for the customer to finish the wiring of his/her board.
Side A/C & Power Supply Detail :
When prepping a board, the customer tells us what they need for power.
T-Trash sells and installs the Voodoo Lab power supplies. (PP-2, PP-Digital & ISO
5)
Many customers already own power supplies and opt to send these to
TT for installation, as the customer must have knowledge on how to hardwire
your power supply to the side a/c.
It does require ‘you’ to cut and strip the a/c cable and hardwire
into the side a/c
T-Trash only gives advice on spec’ing power and signal flow for the customer in Level
3, when we are wiring the entire board
The customer also lets us know what side of the board that they want the
main (male) and courtesy (female) a/c installed
Side-Mount Jacks Detail :
Side-Mount jacks for input/output/stereo/fx send/return/midi/xlr -
etc…
The customer lets us know what side of the board they want them installed
on and if they are part only -$20.00 each for installed but not wired Neutrik
- or if you want us to pre-solder them - (we solder Mogami – Evidence
Monorail or George L’s cable, 6” inches longer than the width
of your board when ordering them ‘wired’) - $30.00 each for
wired Neutrik
Wired Neutrik Detail :
Once you have the prepped board in front of you, you are required
to drill holes in the top, route the cable through and build the plug
on top to finish -
It is safe to drill through the Veltop to finish the wired Neutriks,
but this will have to be redone every time you replace your Veltop
as mentioned in the FAQ’s Section - Why T-Trash Only Custom Wires On Hardtops or
Glowtops and Not On Veltop Pedalboards :
Many customers also send us their loopers, a/b boxes etc… to
install as part of a prepped board – this way, they only have
to send/return & run d/c out to each pedal, making the finish of
the build much easier for the novice.
The prepped board pictured not only illustrates ¼” Neutriks,
and a power supply mounted and wired to side & top a/c’s,
but also has the Large hole cut in the Hardtop for ease of pulling d/c
cables out to each pedal – Hardtops are generally sold w/o the
top hole cut, but if the customer wants this feature, T-Trash will add
for free. All Veltop boards come stock w/ the Large top hole
We also sell the rest of the parts needed to assemble your board as seen on the T-Trash website – see Custom Wiring & Accessory Page for pricing.
Level 3 –
Custom Wired Boards – Available only for USA & Canada
You send your pedals to Trailer Trash Pedalboards for the full wiring
treatment – we design your signal flow, help you order the right
looper, spec your power etc… the end result is seen all over
the T-Trash website – we have designed & custom wired them
all !!!
Turn around times vary due to size of jobs, but we can flip most boards
in 2- 3 days, and usually no more than 4 days even on the big scary
40x18’s –
Your name goes into our queue for wiring based on when we receive a
deposit for order – the deposit for a custom wired board is the
cost of the board/case only – the balance is billed at the end
of the job before shipping to the customer.
As part of our standard procedure, we speak to each customer many
times during the build and also take pictures of the layout of the
board and send to you for approval before we start wiring – It’s
a very tedious process, with excellent & proven results
When the finished board comes to you, all you have to do is open the
case, plug in your instrument, amp and a/c and you’re jammin’ with
a sparkling hot clean signal.
|